INSTRUCTION MANUAL MODEL : SB-5688LCM-CT8x8 HDMI-HDBASET MATRIX SWITCHER8x8 HDMI-HDBaseT Matrix Switch with Extension HDMI-HDBaseT MATRIX SWITCHER SER
8REAR PANELREAR PANEL6. OUTPUT - 1,2,3,4,5,6,7 & 8 HDBaseTCAT Transmitter extend a signal link of HDMI / RS232 / IR Remoteto this RJ-45 Female con
REMOTE CONTROLBefore making any connections to the switcher. Observe the following:> Ensure the mains voltage supply matches the label on the
REMOTE PROTOCOL COMMANDSIR REMOTE CUSTOM AND DATA CODES (NEC Standard)HOW TO SETUP IR CODES : CUSTOM CODE : 09F6 POWER ON : 09F6 A15EPOWER OFF : 0
REMOTE CONTROLROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODESIR CUSTOM AND DATA CODES (NEC Standard)PRESS Number To Select SOURCECUSTOM CODE :
REMOTE CONTROLROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODESIR CUSTOM AND DATA CODES (NEC Standard)PRESS Number To Select SOURCECUSTOM CODE :
EDID FUNCTIONEDID FUNCTION FOR HDMI MATRIX SWITCHEREDID Setup To Change the EDID SetupStep 1. Press the EDID button The display will show the currentl
EDID FUNCTIONNOTE : The already learned EDID cannot be modied. You can only rebuild a new Learning EDID.For example:When the Source has “Learned” the
EDID FUNCTIONEDID FUNCTION FOR HDMI MATRIX SWITCHEREDID Status To view the current EDID status.Step 1. Press EDID button The button will ash blue and
TYPICAL APPLICATIONINSTALLING DIAGRAMSample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335R & SB-5688LCM-CT to co
TYPICAL APPLICATIONINSTALLING DIAGRAMSample connection using IR Transmitters (SB-101) with SB-5688LCM-CT and SB-6335R to control a IR signal from Sate
SAFETY INFORMATION1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipmen
TYPICAL APPLICATIONINSTALLING DIAGRAMSample connection using Audio Extractor to Recode Audio (SB-5609) or to control ARC (SB-5610) and Ext
19IR EXTENDERSB-100 Maximum Distance ~ 984 feet (300 meters)SB-100 and SB-100C Receiver Pin configurationVCC (Ring)Signal (center)GND (Sleeve)TipRing
IR EXTENDER20R o HS /9 5/E CDC 1 2VIR outFrom ReceiverIR inToReceiverCAT6/6a/7OUTPUTR o HS /9 5/E CDC 1 2VIR outFrom ReceiverIR inToReceiverCAT6/6a/
RS-232 SERIAL INTERFACERS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V1.0 & V1.5For a complete list of commands, plea
22ETHERNET SERIAL INTERFACEETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0For a complete list of commands, please re
23LIMITED WARRANTYPLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR
www.shinybowusa.com 1399 Wildre Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa
TABLE OF CONTENTSSAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting
FEATURESPACKAGE CONTENTSCheck that you have the following components;• SB-5688LCM-CT Matrix Switcher • RS-232 V2.0 Protocol Instructions• Ethernet
SPECIFICATIONSSPECIFICATIONS• Type of HDMI Switcher: 8x HDMI inputs To 8x HDMI + 8x HDBaseT Outputs Matrix Switcher• HDMI Support: HD 1080p-@60Hz, H
4FRONT PANELFRONT PANEL1. POWER SWITCHThe power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and
5FRONT PANELFRONT PANEL8. FUNCTION KEY - ALLDisables (mute) video on all destinations OR Selects the same source to all destinations.Option 1 - Press
6FRONT PANELFRONT PANEL12. FUNCTION KEY - RECALLThe system will show previously stored presets, up to a total of 16.Presets are stored in local memory
7REAR PANELREAR PANEL1. DC POWER INLETThe Switcher is tted with a AC power plug input connector. Ensure that the used is of an approved type and is o
Comments to this Manuals